






Study with the several resources on Docsity
Earn points by helping other students or get them with a premium plan
Prepare for your exams
Study with the several resources on Docsity
Earn points to download
Earn points by helping other students or get them with a premium plan
Community
Ask the community for help and clear up your study doubts
Discover the best universities in your country according to Docsity users
Free resources
Download our free guides on studying techniques, anxiety management strategies, and thesis advice from Docsity tutors
Mike Holt Chapter 3 Study Guide Questions and Verified Answers Updated 2025 Graded A
Typology: Exams
1 / 10
This page cannot be seen from the preview
Don't miss anything!
1/4 - ANSSurface-type cabinets, cutout boxes, and meter socket enclosures in damp or wet locations shall be mounted so there is at least ___-in. airspace between the enclosure and the wall or supporting surface. 100 - ANSHandhole enclosure covers shall require the use of tools to open, or they shall weigh over ___ lb. 14 - ANSThe minimum size copper conductor permitted for branch circuits under 600V is ___ AWG. 2 - ANSFor one-family dwellings and the individual dwelling units of two- family and multifamily dwellings, single-phase feeder conductors consisting of ___ ungrounded conductor(s) and the neutral conductor from a 208Y/120 volt system shall be permitted to be sized in accordance with 310.15(B)(7)(1) through (3). 60 - ANSIf cables meeting the requirements in 310.15(B)(3)(4)a through C with more than 20 current-carrying conductors are installed longer than 24 in. without maintaining spacing, are stacked, or are supported on bridle rings, a ___ percent adjustment factor shall be applied.
60 degrees Celsius - ANSType AC cable installed in thermal insulation shall have conductors that are rated at 90 degrees Celsius. The ampacity of the cable in this application shall not exceed that of a ___ rated conductor. Aluminum - ANS___ is a nonferrous, nonmagnetic metal that has no heating due to hysteresis heating. Angle - ANSIn an FMC installation, ___ connectors shall not be concealed. approved - ANSIMC, elbows, couplings, and fittings shall be permitted to be installed in concrete, in direct contact with the earth, or in areas subject to severe corrosive influences where protected by corrosion protection ___ for the condition. at intervals not exceeding 4 1/2 ft - ANSFMC shall be supported and secured ___. be listed and identified for such use - ANSType MC cable shall be listed and fittings used for connecting Type MC cable to boxes, cabinets, or other equipment shall ___. C. A and B - ANSAt type AC cable terminations, a(n) ___ shall be provided. A. fitting (or box design) that protects the conductors from abrasion B. insulating bushing between the conductors and the cable armor C. A and B D. none of these
couplings - ANSRunning threads shall not be used on RMC for connections at ___. D. A and B - ANSCable trays shall be ___ except as permitted by 392.18(D). A. exposed B. accessible C. concealed D. A and B D. A or B - ANSAll conductors of the same circuit shall be ___, unless otherwise specifically permitted in the Code. A. in the same raceway or cable B. in close proximity in the same trench C. the same size D. A or B D. A or B - ANSAluminum raceways, cable trays, cablebus, auxiliary gutters, cable armor, boxes, able sheathing, cabinets, elbows, couplings, nipples, fittings, supports, and support hardware ___ shall be provided with supplementary corrosion protection. A. embedded or encased in concrete B. in direct contact with the earth C. likely to become energized D. A or B
D. A or B - ANSConduits or raceways through which moisture may contact live part shall be ___ at either or both ends. A. sealed B. plugged C. bushed D. A or B D. A or B - ANSWhere type NM cables pass through cut or drilled slots or holes in metal members, the cable shall be protected by ___ which are installed in the opening prior to the installation of the cable and which securely cover all metal edges. A. listed bushings B. listed grommets C. plates D. A or B D. All of these - ANSBackfill used for underground wiring shall not damage, ___ or prevent adequate compaction of fill or contribute to corrosion. A. raceways B. cables C. conductors D. all of these D. all of these - ANSIn industrial facilities where conditions of maintenance and supervision ensure that only qualified persons will service the installation, able tray systems can be used to support ___. A. raceways
B. within 5 ft of a box or termination fitting when structural members do not readily permit the raceway to be secured within 3 ft of the termination C. except when the IMC is within 3 ft of the service head for an above-the- roof termination of a mast D. any of these D. any of these - ANSType NM and Type NMC cables shall be permitted in ___, except as prohibited in 334.12. A. one-and two-family dwellings and their attached/detached garages and storage buildings B. multifamily dwellings permitted to be Types III, IV, and V construction C. other structures permitted to by of Types III, IV, and V construction D. any of these dry locations - ANSA multioutlet assembly can be installed in ___. False - ANSTrue or False: Type UF cable can bed used in commercial garages flame retardant - ANSENT is composed of material resistant to moisture and chemical atmospheres, and is ___. four - ANSA run of RMC shall not contain more than the equivalent of ___ quarter bend(s) between pull points such as conduit bodies and boxes.
framing members - ANSHorizontal runs of RMC supported by openings through ___ at intervals not exceeding 10 ft and securely fastened within 3 ft of termination points shall be permitted. Listed - ANSFor locations not specifically identified in Table 300.5, a lesser cover depth than required in Column 5 shall be permitted where specified in the installation instructions of a(n) ____ low-voltage lighting system. listed - ANSFor the purposes of 350.30, ___ LFMC fittings shall be permitted as a means of securement and support. listed - ANSOutlet boxes required in 314.27 shall be permitted to support ___ locking support and mounting receptacles used in combination with compatible attachment fittings. listed for wet locations - ANSThreadless couplings and connectors used with RMC in wet locations shall be ___. no greater than the number for which it was designed - ANSThe maximum number of conductors permitted in any surface metal raceway shall be ___. not required after installation - ANSWhere flexibility is ___, liquidtight flexible metal conduit shall be permitted to be used as an equipment grounding conductor when installed in accordance with 250.118(6).
True - ANSTrue or False: The cut ends of PVC conduit shall be trimmed to remove the burrs and rough edges. True - ANSTrue or False: The service or feeder ratings addressed by 310.15(B)(7) are based on the standard ampacity rating from 240.6(A).