


















Study with the several resources on Docsity
Earn points by helping other students or get them with a premium plan
Prepare for your exams
Study with the several resources on Docsity
Earn points to download
Earn points by helping other students or get them with a premium plan
Community
Ask the community for help and clear up your study doubts
Discover the best universities in your country according to Docsity users
Free resources
Download our free guides on studying techniques, anxiety management strategies, and thesis advice from Docsity tutors
IRONWORKER NCCER EXAM 2025 | ALL QUESTIONS AND CORRECT ANSWERS | GRADED A+ | VERIFIED ANSWERS | LATEST EXAM | JUST RELEASED
Typology: Exams
1 / 26
This page cannot be seen from the preview
Don't miss anything!
Most of the SMAW weld applications encountered will______beads when welding a single pass weld or on the first pass of a multiple pass weld. ------ ---CORRECT ANSWER-----------------stringer If the notation for a wide-flange beam is W12×14×8'6", the 14 indicates______. ---------CORRECT ANSWER-----------------weight per foot of the beam in pounds. During the shaking out, which of the following should be marked on each piece, in addition to the fabricators mark? ---------CORRECT ANSWER------ -----------the centerline or balance point of the piece. Before a column can be erected, the shims or leveling nuts in place should be checked to ensure that they are set at the proper______. --------- CORRECT ANSWER-----------------elevation The location of the anchor bolt in relation to other anchor bolts in the same pattern should not deviate more than + or - ---------CORRECT ANSWER---- -------------1/ When columns are erected ironworkers should only erect______. --------- CORRECT ANSWER-----------------as many as can be tied together with beams that day.
When can plumbing of structural members start? ---------CORRECT ANSWER-----------------As soon as the raising gang erects the first elevation of columns and beams or a tier of columns and beams. The simplest plumbing tool, consisting of a line with a brass weight on it is a______. ---------CORRECT ANSWER-----------------plumb bob The main difference between A325 and A490 bolts is______. --------- CORRECT ANSWER-----------------the amount of tensile strength they can withstand before failure. The formula for calculating the length of the bolt needed is______. --------- CORRECT ANSWER-----------------Length of bolt = thickness of metal(grip)
The two commonly used natural fiber ropes are Manila and sisal, but the only type suitable for construction rigging is______. ---------CORRECT ANSWER-----------------number 1 grade Manila Which of the following types of rope is the strongest? ---------CORRECT ANSWER-----------------nylon Which of the following ropes is most likely to lose considerable tensile strength if it is wet before coiling? ---------CORRECT ANSWER----------------- natural fiber rope What is the appropriate factor of safety for a ropes capacity in terms of breaking strengths? ---------CORRECT ANSWER-----------------10 when hoisting personnel What is a bend or U-shaped curve in a line? ---------CORRECT ANSWER--- --------------bight What knot is the universal knot that never jams or slips if properly tied? ----- ----CORRECT ANSWER-----------------clove hitch Blocks, when Reeved, work like a machine and are not 100% efficient because of______. ---------CORRECT ANSWER-----------------friction
Which of the following is a sign that the blocks are being overloaded? ------- --CORRECT ANSWER-----------------hook shows signs of opening. If reeving a pair of tackle blocks, one of which has more than two sheaves, which sheave should the lead line go? ---------CORRECT ANSWER---------- -------center sheave of the upper block. The kindling temperature of steel is ---------CORRECT ANSWER-------------- ---1600 degrees One advantage of the OFC process is that it is ---------CORRECT ANSWER-----------------portable The materials that can be cut with OFC are limited primarily to _______materials ---------CORRECT ANSWER-----------------ferrous A welder opens the cylinder valve slightly and closes it immediately. what process did he/she perform? ---------CORRECT ANSWER----------------- cracking the cylinder A device that prevents the reverse flow of gasses that would result in a combustible mixture in the welding hose is a ---------CORRECT ANSWER-- ---------------check valve A condition in which the flame burns inside the tip, torch or hose is known as a ---------CORRECT ANSWER-----------------flashback
what is the term for the weight of all moving and constantly acting loads? --- ------CORRECT ANSWER-----------------live load which of the following is not one of the three basic components of concrete? ---------CORRECT ANSWER-----------------lime which of the following is the most accurate range of strengths for concrete? ---------CORRECT ANSWER-----------------3000 to 20,000 psi when reinforcing concrete, what does the steel add to the concrete? --------- CORRECT ANSWER-----------------tensile strength what size wire is used to tie most rebar? ---------CORRECT ANSWER-------- --------- 16 which of the following is a low foundation wall of sufficient depth to extend below the frost line? ---------CORRECT ANSWER-----------------grade beam concrete is strong in compression and______, but weak in______. --------- CORRECT ANSWER-----------------shear, tension what are the small "U" or "W" shaped bars placed across a beam to resist diagonal tension known as? ---------CORRECT ANSWER----------------- stirrups
Bar supports are also referred to as ---------CORRECT ANSWER-------------- ---accessories the function of the______is to safely transmit the superstructure loads to the ground without causing settlement. ---------CORRECT ANSWER---------- -------foundation in order to connect the column to its supports,______are required. --------- CORRECT ANSWER-----------------dowels in erecting a wall where the footings have been previously doweled, it is necessary for all dowels to be______and______. ---------CORRECT ANSWER-----------------straight, in-line columns are made up of vertical bars and ---------CORRECT ANSWER------ -----------bands or ties what are the end supports for a beam bridge called? ---------CORRECT ANSWER-----------------abutments SMAW uses which of the following electrode polarities? ---------CORRECT ANSWER-----------------all of the above
An electrode is classified as E7024. What does the 2 stand for? --------- CORRECT ANSWER-----------------flat and horizontal An electrode is classified as E6010. What does the 60 stand for? --------- CORRECT ANSWER-----------------tensile strength Which of the following is the first step to follow when choosing a SMAW electrode for a specific welding application? ---------CORRECT ANSWER--- --------------select the required tensile strength What can be the result of low hydrogen rods picking up moisture in the coating? ---------CORRECT ANSWER-----------------hydrogen-induced cracking of the weld. What SMAW technique is used to force the arc to stay ahead of the puddle? ---------CORRECT ANSWER-----------------drag angle In figure 8.1, the A is the______angle and B is the______angle. --------- CORRECT ANSWER-----------------travel, work figure 3.2 illustrates a______. ---------CORRECT ANSWER----------------- seven-part fall
within the round strand classification, the wires may be arranged in certain geometric patterns called______. ---------CORRECT ANSWER----------------- constructions For rigging ropes, the minimum acceptable factor of safety is______. --------
RIGGING? ---------CORRECT ANSWER-----------------Slings, shackles, and spreader beam WHAT IS USED TO PREVENT JOIST FROM MOVING LATERALLY? ------ ---CORRECT ANSWER-----------------X-BRIDGING RESPIRATORS SHOULD BE USED IF WELDING ---------CORRECT ANSWER-----------------IN A CONFINED SPACE THE BUILDINGS FRAME BEFORE BEING PERMANENTLY FASTENED MUST BE: ---------CORRECT ANSWER-----------------PLUMB WHAT DOES MSDS STAND FOR? ---------CORRECT ANSWER-------------- ---Material Safety Data Sheet ALL OF THE FOLOWING ARE TRUE ABOUT THE SAFE USE OF SHACKLES EXCEPT: ---------CORRECT ANSWER-----------------SCREW PINS SHOULD BE BACKED OFF TWO TURNS