Partial preview of the text
Download Iicrc wrt exam with questions and answers and more Exams Search Engine Optimization and Advertising (SEO and SEM) in PDF only on Docsity!
When it comes to every water loss, the first thing that should be done is to carry out a hazard and risk assessment. Answer the following questions if you are a technician who is required to wear respiratory protection: Training, mask fitting, and medical evaluation were all performed. To answer your question, lead and asbestos are two harmful compounds that are frequently seen in older buildings. Without a signed ANSWER work authorization, water damage restoration work will never get underway before it is completed. As part of the preparatory inspection, restorers should carry out the following to reduce the amount of damage that is caused to the building's materials and contents. - ANSWER Services for the mitigation of losses When pre-existing damage is identified, technicians are obligated to provide information and communication to all parties who have a material interest in the matter concerning the harm. Please document and discuss your ANSWER. When attempting to detach the carpet from the tackless strip, technicians should always make use of a and a .- The ANSWER was a knee kick and a carpet awl. Carpet delimitations are primarily justified by the following reasons: ANSWER damage that was caused by water When the pad is being removed, the wet carpet is folded. Excessively forceful removal Heaving hefty objects around A great deal of foot traftic Incorrect installation Pee from pets Materials that are most susceptible to secondary damage are those that are . It is a hygroscopic answer. Over % Relative humidity encourages the growth of microorganisms, and secondary damage can take place in hygroscopic materials. - The answer is sixty percent Water that falls into the category of was obtained from a hygienic source and does not provide a significant risk to human beings. Answer 1: [No] There is a substantial amount of contamination in water that falls into the category of , and it has the potential to cause pain or sickness in humans if they come into touch with it or drink it. To assist in the remediation evaluation, restorers should take into consideration the utilization of a in the event of a Category 3 water intrusion with heightened risk scenarios. ANSWER Professional in the field of indoor environmental issues (TEP) Technicians need to erect , perform the required , and install while they are operating in Technicians should evaluate all locations that could be possibly affected by water damage while they are inspecting a structure that has been harmed by water exposure. The water losses that fall into the category of class _____ contain the least amount of water absorption and evaporation load. This category is characterized by wet, porous materials that account for less than five percent of the total surface area of the floor, walls, and ceiling in the region. Class ___ water losses include a considerable amount of water absorption and evaporation load, and moist, porous materials account for between 5 and 40 percent of the total surface area of the space, which includes the floor, the walls, and the ceiling. ANSWER 2 When wet, porous materials account for more than forty percent of the total surtace areas of the walls, floors, and ceilings, and when low evaporation materials or assemblies have absorbed only a small quantity of moisture, the most significant amount of water absorption and evaporation load is found in a Class - ANSWER 3 structure. There is a class of water incursion known as ANSWER 4, which is characterized by a substantial volume of water absorption that is bound within low evaporation materials and may necessitate prolonged drying durations. The use of moisture detection equipment is recommended in order to measure and document the activities of and . Moisture content and relative humidity data are included in the answer. The extent of water migration in carpet and pad can be determined with the help of a moisture sensor, which is the subject of the following sentence: ANSWER: The thermo-hygrometer is a device that measures both temperature and humidity. A ANSWER moisture meter is utilized in order to ascertain dry standards and measure the levels of moisture present in the materials that are used for structural purposes. It is recommended that restorers use a moisture meter that is either non-invasive or non-penctrating in order to find moisture beneath ceramic tile. Although they are not capable of detecting moisture, infrared cameras and thermal imaging can be helpful in determining whether or not a substance is likely to be wet. In the process of moisture evaporating from materials, the surface of such materials experiences a decrease in temperature. In the case of water damage caused by Cat 2 and Cat 4, is always eliminated. - The ANSWER A pad or cushion for carpeting It is recommended that damaged particle board be removed and replaced. ANSWER removal and replacement of damaged particle board As the temperature of the air rises, the relative humidity will decrease according to the answer. Given a sample of wet air, the ratio of the mass of water vapor to the mass of dry air is stated in grains per pound of dry air. The answer to this question is the humidity ratio, which is denoted by the acronym GPP. According to the humidity ratio, another psychrometric property that also increases (or lowers) as the humidity ratio grows or decreases is: - The answer is the vapor pressure and the dew point The vapor pressure is the pressure that is imposed by the molecules of the vapor on the surface that is surrounding them. Water vapor pressure is constantly looking for Equilibrium is the answer." In the event that the vapor pressure in the surrounding air is lower than the vapor pressure in the materials that are wet, the result will be something called condensation. By increasing the rate of evaporation, wall cavities can be dried out quickly through the process of blowing air into them. Dew point temperature is the temperature at which the relative humidity in the air achieves a level of saturation, which is equal to one hundred percent relative humidity. Keeping the surface temperature at a level that is higher than the dew point will make it possible for evaporation to take place. Transforming a liquid into a vapor is the process that is referred to as . Answer: evaporation of water ANSWER Saturated air is the state of air that occurs when it is able to hold the greatest quantity of water vapor that is possible at a particular temperature. It is important to note that the pace of evaporation is substantially influenced by the temperature of the affected areas as well as the temperature of wet materials. An increase in the temperature of wet materials results in an increase in the amount of energy that is available for evaporation to take place. Adding heat to materials is a method that promotes drying, according to the answer energy Increasing the temperature of wet materials or assemblies, which in turn raises the material's , can be accomplished by a variety of methods, one of which is the application of direct heat. ANSWER the pressure of the vapor Dehumidifiers that use refrigerants are able to remove moisture from the air by means of a process known as condensation. The optimal performance range for refrigerants is between 70 and 90 degrees Fahrenheit, according to the answer. Low grain refrigerant (LGR) dehumidifiers are designed to lower the vapor pressure of a refrigerant that is below a certain threshold. It is a usual answer. To what extent does the type of dehumidifier generate air with the lowest vapor pressure? Desiccant is the answer. Desiccants are the most efficient dehumidifiers to utilize when drying up a crawlspace that is chilly and wet. ANSWER Desiccants Tt is advised that the initial water removal be 425 PPD while employing an LGR dehu in a class 3 water incursion that contains 17,000 square feet of space. What is the appropriate amount of water removal? When employing an LGR that removed 130 pints per day (PPD) under AHAM test circumstances, the suggested number of dehus initially on a class 2 water incursion with 35,000 square feet of total area is - ANSWER 6 The initial recommended figure for a class 4 water intrusion in a facility that is 5,000 square feet in size and has a ceiling height of cight fect is - ANSWER | when using a desiccant dehumidifier that is rated to treat 400 cubic feet per minute. The depiction of the impacted area that illustrates the amount of water migration is referred to as a . - The Moisture Map, the Answer Through the circulation of air in regions where contamination is already present, the likelihood of polluting areas can be increased. - ANSWER Unaffected by the Event Customers should be advised by restorers to the structure for the period of time during and after the application of biocides. This should be done before the biocides are applied. - ANSWER exit the premises These are the products that are used to lower the number of germs to levels that are regarded safe according to public health laws or regulations, but they do not necessarily climinate them entirely. Sanitizers are the answer. Products that eliminate or render inactive at least 99 percent of disease-causing bacteria that are found on inanimate items, but do not necessarily eliminate their spores for the following reasons: - Disinfectants Are the Answer When applying biocides or antimicrobials, technicians are required to adhere to the directions provided on the label in order to ensure the correct application. If the humidity ratio is 132 GPP, what is the temperature at which the dew point occurs? ANSWER: 75 degrees Fahrenheit The indoor parameters for a drying project are 80% relative humidity and 80% temperature. What temperature is required to bring the relative humidity up to 35%? - The ANSWER 102 to 103 degrees Fahrenheit What is the temperature at which condensation starts to form on structural materials when the temperature inside is 75 degrees and the relative humidity is 65% - The ANSWER at 63 degrees (the dew point) The relative humidity is: - ANSWER 40-42% at 95 degrees Fahrenheit and 55 grams per square meter The answer to the question, "Which atmospheric conditions have the lowest vapor pressure, 80 degrees and 60% relative humidity, or 40 degrees and 75% relative humidity?" is 40 degrees and 75% relative humidity. 
