Download Dilutions in Molecular Biology: Understanding Concentrations and Volumes and more Study notes Molecular biology in PDF only on Docsity!
Dilutions
Occasionally a solution is too concentrated to be used as it is. For example, when one is
performing manual blood counts, the blood contains too many cells to be counted as such. Or
when performing a given test, it may be found that the concentration of the substance being
measured is too high for measurement with a certain instrument. In such cases, a dilution is
necessary.
Laboratory procedures in which an amount of one substance is added to another to
reduce the concentration of one of the substances are referred to as dilutions. A dilution usually
means the volume of original substance in the total volume of final solution.
In dilution statements, the smaller number is the number of parts of the substance that is
being diluted; the larger number refers to the total number of parts in the final solution unless
explicitly stated otherwise. All of the following statements mean the same thing:
- Make a 1 to 10 dilution of serum in saline.
- Make a 1 in 10 dilution of serum in saline.
- Make a 1 to 10 dilution of serum with saline.
- Make a 1/10 dilution of serum with saline.
- Dilute the serum 10 times with saline
- Make a dilution of 1 part serum and 9 parts saline.
- Make a dilution of 1 part serum to 9 parts saline.
- Make a 1:9 dilution of serum and saline.
The first five statements are symbolically shown as "1/10" dilutions and the last three are
shown as "1:9" dilutions. Terms such as "1/10", "1/100", "1/500", etc. are called dilution factors.
In each of the preceding dilutions, the numerator, 1, refers to the number of parts of serum and
the denominators, 10, 100, 500, refer to the number of total parts of each dilution. Saline is
called “diluent” in the above statements. Also note that in the preceding statements, the
directions can be followed by combining 1 ml of serum with 9 ml of saline to make 10 ml of the
final solution, by adding 2 oz. of serum to 18 oz. saline, etc. In all cases, there is 1 part of the
original substance in 10 parts of the final solution.
1 part of the concentrated material
- 9 parts of the diluent____
10 parts of the final solution
Example: 5 ml of serum is diluted to 25 ml with saline. What is the serum dilution?
Set up the problem as 5 ml serum + X ml saline = 25 ml of the final solution.
X = 25 - 5
X = 20 ml of saline
The serum dilution is the amount of serum in the amount of total solution; hence, this is a
5/25 serum dilution which would equal a 1/5 dilution.
Series of Dilutions
Two important points should be considered in dilutions: how each dilution is made and
what each dilution contains. The important consideration is the concentration of the materials in
the dilution. However, it is first necessary to know how a dilution was made. A general rule to
use in calculating the concentration of solutions in a series is to multiply the original
concentration by the first dilution factor, this by the second dilution factor, this by the third
dilution factor, and so on until the final concentration is known.
Example: A 5M solution of HCl is diluted 1/5. The resulting solution is diluted 1/10. Determine
the concentration of each of the solutions.
In this example, one solution is made from a solution that was made from yet another.
To calculate the concentration of any of the solutions in such a series, first express all dilutions
as a fraction, then multiply the concentration of the beginning solution by the dilution factor used
in each succeeding step. The following steps are used in solving this example.
- The concentration of the first solution is given as 5M HCl. This then is the first answer.
- The second solution was made by a 1/5 dilution of the first solution. The concentration of HCl
in the second solution would be calculated by multiplying the concentration of the first solution
by the dilution factor used to produce the second solution. Hence, the second solution has an
HCl concentration of 1M.
5M HCl x 1/5 = 5M/5 =1M
- To calculate the concentration of HCl in the third solution in the series, multiply the original
concentration of HCl by the value of each succeeding dilution factor.
5M x 1/5 x 1/10 = 5M/50 = 1M/
Therefore, the concentration of HCl in the last solution is 0.1M.
Notice that in each solution of this problem the concentration is expressed in molarity.
This is because the concentration of the original solution was measured in molarity. In this type
of problem the concentration of each dilution will be expressed in the same unit as that used in
the original solution.
The calculations used to determine the concentration of each solution in a series may be
used in reverse to produce a dilution series having prescribed concentrations at each step.
Example: Make the following dilutions of serum in buffer: 1/10, 1/100, and 1/500.
Before attempting to solve such a problem, it should be mentioned that any one dilution
could usually be made by several procedures depending on how large a volume of the final
solution is needed and how much of the original solution (to be diluted) is available. For
example, in the problem above, we may need only 10 ml of the 1/500 dilution, so if we take 1 ml
of the original serum and add 499 ml of buffer, we will be left with a large volume of a solution,
most of which is of no use to us. Additionally, storage space is a precious commodity to many
research and health workers. Now back to solving our original problem.
This would produce 100 ml of a 1/10,000 dilution of stock in water.
Any combination of dilutions that will yield a final concentration of 1/10,000 may be used.
As mentioned earlier, the combination is determined in part by the glassware available and the
volume needed.
Determining Volumes and Concentrations
To decide what dilution to use, one needs to know several things:
- Original concentration of the substance being diluted
- Final volume desired
- Final concentration desired
- Number of dilutions to be made (at times)
Example: A 1/200 stock solution of boric acid is on hand. The procedure requires 50 ml of a
1/500 solution. How would the necessary amount be made without making excess?
Going from 1/200 to 1/500 produces a 2/5 ratio. This ratio is found by X below:
(1/200) X = (1/500)
X = (200/500) = 2/
This means taking 2 parts of the original boric acid solution and bringing up the volume to 5
parts. So, if we need 50 parts (1 part = 1 ml), we should take 20 ml of the stock.
A quick way to do problems of this sort is to use the famous formula:
C
V
= C
V
where C 1
and C2 are concentrations of solutions 1 and 2 and V 1
and V 2
are their respective
volumes. If we fill the parts for the problem at hand, we will have:
(1/200) V
Solving the fractions for V 1
, we get V 1
= 20 ml. Again this means that if we take 20 ml of the
stock boric acid and add 30 ml water, we would have 50 ml of the desired solution.
Some Final Notes
1. After doing your calculations, it is always a good idea to work backwards and see if you come
up with the original data given. This is a good check as to the correctness of your calculations.
2. When working with very large or very small numbers, it is customary to convert them to a
number between 1 and 9, times a power of base 10. For example:
32,000,000 = 3.2 x 10
0.000047 = 4.7 x 10
Note in the above examples that (a) the first number in the conversion is between 1 and 9 and
(b) the power of base 10 can be positive or negative. A positive power means the number is
large(r than 1) and a negative power means the number is small(er than 1).
Dilution factors are similarly converted to powers of 10. For example:
Similarly, reciprocals of dilution factors can be converted to powers of 10 as well. For example:
3. Units of measurements can be converted as follows:
1 Kg = 1000 g
1 g = 1000 mg
1 mg = 1000 μg
1 μg = 1000 ng
1 ng = 1000 pg
1 liter = 1000 ml
1 ml = 1000 μl
4. Although already mentioned at the beginning of this chapter, it is worth repeating that "the
original solution is always more concentrated (think big numbers, possibly with positive powers)
than the diluted samples (think small numbers, possibly with negative powers)”. Check these
rules of thumb whenever you are confronted with a dilution problem. Can you verify these rules
in the preceding examples?
5. The ratio of the numbers rather than the numbers themselves is important. For example, 1 ml
in 10 ml, 0.1 ml in 1.0 ml, 5 ml in 50 ml, etc. all give the same dilution (ratio). The only
differences are the amounts of the individual constituents as well as the final product.
6. Log on to “http://www.bio.upenn.edu/computing/media/Instructional.Dilution.php” to see a
video explaining dilutions.
Use of any section of this Lab Manual without the written consent of Dr. Eby Bassiri, Dept. of
Biology, University of Pennsylvania is strictly prohibited.
